5G Technology World

  • 5G Technology and Engineering
  • FAQs
  • Apps
  • Devices
  • IoT
  • RF
  • Radar
  • Wireless Design
  • Learn
    • 5G Videos
    • Ebooks
    • EE Training Days
    • FAQs
    • Learning Center
    • Tech Toolboxes
    • Webinars/Digital Events
  • Handbooks
    • 2024
    • 2023
    • 2022
    • 2021
  • Resources
    • Design Guide Library
    • EE World Digital Issues
    • Engineering Diversity & Inclusion
    • Engineering Training Days
    • LEAP Awards
  • Advertise
  • Subscribe

Atomically Thin Device Promises New Class of Electronics

By Staff Author | October 22, 2013

Mark HersamAs electronics approach the atomic scale, researchers are increasingly successful at developing atomically thin, virtually two-dimensional materials that could usher in the next generation of computing. Integrating these materials to create necessary circuits, however, has remained a challenge.

Northwestern University researchers have now taken a significant step toward fabricating complex nanoscale electronics. By integrating two atomically thin materials — molybdenum disulfide and carbon nanotubes — they have created a p-n heterojunction diode, an interface between two types of semiconducting materials.

“The p-n junction diode is among the most ubiquitous components of modern electronics,” said Mark Hersam, Bette and Neison Harris Chair in Teaching Excellence in the Department of Materials Science and Engineering at Northwestern’s McCormick School of Engineering and Applied Science and director of the Northwestern University Materials Research Center. “By creating this device using atomically thin materials, we not only realize the benefits of conventional diodes but also achieve the ability to electronically tune and customize the device characteristics. We anticipate that this work will enable new types of electronic functionality and could be applied to the growing number of emerging two-dimensional materials.”

The isolation over the past decade of atomically thin two-dimensional crystals — such as graphene, a single-atom-thick carbon lattice — has prompted researchers to stack two or more distinct two-dimensional materials to create high-performance, ultrathin electronic devices. While significant progress has been made in this direction, one of the most important electronic components — the p-n junction diode — has been notably absent. 

Among the most widely used electronic structures, the p-n junction diode forms the basis of a number of technologies, including solar cells, light-emitting diodes, photodetectors, computers, and lasers. 

In addition to its novel electronic functionality, the p-n heterojunction diode is also highly sensitive to light. This attribute has allowed the authors to fabricate and demonstrate an ultrafast photodetector with an electronically tunable wavelength response. 

The research, “Gate-Tunable Carbon Nanotube-MoS2 Heterojunction p-n Diode,” was published October 21 in the Proceedings of the National Academy of Sciences.

In addition to Hersam, leading the research were Lincoln Lauhon, professor of materials science and engineering, and Tobin Marks, Vladimir N. Ipatieff Professor of Catalytic Chemistry and (by courtesy) Materials Science and Engineering.

Other authors of the paper are postdoctoral researchers Vinod Sangwan, Chung-Chiang Wu, and Pradyumna Prabhumirashi, and graduate students Deep Jariwala and Michael Geier, all of whom are affiliated with Northwestern University.

This research was supported by the National Science Foundation-funded Materials Research Science and Engineering Center (MRSEC) and the Office of Naval Research.


Filed Under: RF

 

Next Article

← Previous Article
Next Article →

Related Articles Read More >

Open RAN test service adds colocation capabilities
Switch operates DC to 20 GHz with 128 configurable connection states for asymmetric SerDes testing
Butler Matrix
Butler Matrix drives Wi-Fi and other phased-array antennas
Long-wire dipole antennas: still viable after more than a century

Featured Contributions

  • Overcome Open RAN test and certification challenges
  • Wireless engineers need AI to build networks
  • Why AI chips need PCIe 7.0 IP interconnects
  • circuit board timing How timing and synchronization improve 5G spectrum efficiency
  • Wi-Fi 7 and 5G for FWA need testing
More Featured Contributions

EE TECH TOOLBOX

“ee
Tech Toolbox: 5G Technology
This Tech Toolbox covers the basics of 5G technology plus a story about how engineers designed and built a prototype DSL router mostly from old cellphone parts. Download this first 5G/wired/wireless communications Tech Toolbox to learn more!

EE LEARNING CENTER

EE Learning Center
“5g
EXPAND YOUR KNOWLEDGE AND STAY CONNECTED
Get the latest info on technologies, tools and strategies for EE professionals.

Engineering Training Days

engineering
“bills
5G Technology World
  • Enews Signup
  • EE World Online
  • DesignFast
  • EDABoard Forums
  • Electro-Tech-Online Forums
  • Microcontroller Tips
  • Analogic Tips
  • Connector Tips
  • Engineer’s Garage
  • EV Engineering
  • Power Electronic Tips
  • Sensor Tips
  • Test and Measurement Tips
  • About Us
  • Contact Us
  • Advertise

Copyright © 2025 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy

Search 5G Technology World