5G Technology World

  • 5G Technology and Engineering
  • FAQs
  • Apps
  • Devices
  • IoT
  • RF
  • Radar
  • Wireless Design
  • Learn
    • 5G Videos
    • Ebooks
    • EE Training Days
    • FAQs
    • Learning Center
    • Tech Toolboxes
    • Webinars/Digital Events
  • Handbooks
    • 2024
    • 2023
    • 2022
    • 2021
  • Resources
    • Design Guide Library
    • EE World Digital Issues
    • Engineering Diversity & Inclusion
    • Engineering Training Days
    • LEAP Awards
  • Advertise
  • Subscribe

RF Testing of Space Antenna Coatings

By European Space Agency | August 3, 2016

Candidate coatings for a new space antenna undergoing testing at ESA’s technical heart in the Netherlands.

“Protective coatings safeguard antennas against temperature extremes or other environmental factors such as ultraviolet radiation,” explains antenna engineer Elena Saenz, performing the testing at ESA’s technical centre in Noordwijk.

“Working with industry, we were asked to evaluate several candidate coatings for the coming MetOp microwave imager – which sounds the atmosphere at various frequencies to gather data on rainfall, water vapour, temperature and clouds.

“The testing needs to measure the radio frequency behaviour of sample coatings across a very wide range of frequencies, from 18.7 GHz up to a maximum 191.3 GHz – checking, for instance, that they do not cause unacceptable signal losses.”

Feed horns send out radio signals to be reflected across the table to the coating and back again, to assess performance.

Two of the candidates proved most promising to coat the carbon-fibre reinforced polymer honeycomb microwave imager antenna. ESA’s antenna test facilities carry out around several of these kind of campaigns annually.

Higher frequencies were tested on the cleanroom tabletop system seen here, while testing for lower frequencies below 50 GHz was undertaken in ESA’s Compact Antenna Test Range, normally used for antenna testing but adaptable for materials testing as well.


Filed Under: RF

 

Next Article

← Previous Article
Next Article →

Related Articles Read More >

Butler Matrix
Butler Matrix drives Wi-Fi and other phased-array antennas
Long-wire dipole antennas: still viable after more than a century
RemCom Wireless InSite 4.0
Software simulates RF conditions from the Earth to the Moon
FAQ on the Butler matrix for beamforming: part 2

Featured Contributions

  • Overcome Open RAN test and certification challenges
  • Wireless engineers need AI to build networks
  • Why AI chips need PCIe 7.0 IP interconnects
  • circuit board timing How timing and synchronization improve 5G spectrum efficiency
  • Wi-Fi 7 and 5G for FWA need testing
More Featured Contributions

EE TECH TOOLBOX

“ee
Tech Toolbox: 5G Technology
This Tech Toolbox covers the basics of 5G technology plus a story about how engineers designed and built a prototype DSL router mostly from old cellphone parts. Download this first 5G/wired/wireless communications Tech Toolbox to learn more!

EE LEARNING CENTER

EE Learning Center
“5g
EXPAND YOUR KNOWLEDGE AND STAY CONNECTED
Get the latest info on technologies, tools and strategies for EE professionals.

Engineering Training Days

engineering
“bills
5G Technology World
  • Enews Signup
  • EE World Online
  • DesignFast
  • EDABoard Forums
  • Electro-Tech-Online Forums
  • Microcontroller Tips
  • Analogic Tips
  • Connector Tips
  • Engineer’s Garage
  • EV Engineering
  • Power Electronic Tips
  • Sensor Tips
  • Test and Measurement Tips
  • About Us
  • Contact Us
  • Advertise

Copyright © 2025 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy

Search 5G Technology World